- 07/01/2026
- 1min
July 2026
Pro-Line Engine Flush
Show details
Pro-Line Engine Flush
Pro-Line Engine Flush
Properties
- highly economical
- suitable for diesel particulate filters
- does not attack common sealing materials
- tested for turbochargers and catalytic converters
- gentle cleaning
- simple to use
- rapid cleaning
Application
One full can (500 ml) used with 3–5 Liters (3.2 to 5.3 U.S. Qts) of motor oil. 5 l used with 30-50 Liters (32 to 53 U.S. Qts) of motor oil.
Add Pro-Line Engine Flush to the engine oil at operating temperature before changing the oil.
After adding the product allow the engine to idle for 10 to 15 minutes depending on the degree of contamination.
Then change the oil and the filter.
Cera Tec
Show details
Cera Tec
Cera Tec
Properties
- highest thermal stability
- tested for turbochargers and catalytic converters
- increases smooth operation
- miscible with all commercially available motor oils
- long engine service life
- excellent high and low temperature behavior
- Reduces friction losses in the engine
- Protects the engine in emergency running conditions
- Reduces wear during cold starts and while operating
- stable under extreme pressures
- chemically inert
- compatible with fine filters
- suitable for diesel particulate filters
Application
One full can (300 ml) used with 3–5 Liters (3.2 to 5.3 U.S. Qts) of motor oil. Long-term effect up to 50,000 km (30,000 miles). Shake well before use. Not suitable for use with DSG/DCT-, automatic-transmissions or wet-clutch differentials.
For best protection, use with every oil change.
MoS2 Anti-Friction Engine Treatment
Show details
MoS2 Anti-Friction Engine Treatment
MoS2 Anti-Friction Engine Treatment
Properties
- increases smooth operation
- miscible with all commercially available motor oils
- reduces oil and fuel consumption
- reduces operating wear
- absolutely compatible with filters
Application
One full can (300 ml) used with 3–6 Liters (3.2 to 6.4 U.S. Qts) of motor oil. The product is self-mixing and can be added at any time. Shake well before use. For best protection, use with every oil change.
Hydraulic Lifter Additive
Show details
Hydraulic Lifter Additive
Hydraulic Lifter Additive
Properties
- tested for turbochargers and catalytic converters
- dampens hydraulic tappet noise
- cleans valve bores
- improves the lubrication properties of the oil
Application
One full can (300 ml) used with 3–6 Liters (3.2 to 6.4 U.S. Qts) of motor oil.
The product is self-mixing and can be added at any time. Shake well before use. For best results, use with every oil change.
Motor Oil Saver
Show details
Motor Oil Saver
Motor Oil Saver
Properties
- prevents oil leaks and pollution of the environment
- maintains and regenerates rubber and plastic seals
- reduces oil consumption
- prevents smoking
- reduce engine noise
Application
One full can (300 ml) used with 3–5 Liters (3.2 to 5.3 U.S. Qts) of motor oil. The product is self mixing and can be added at any time, sealing first takes effect after about 600-800 km (400-500 miles).
The use of Motor Oil Saver every around 30.000 Km (20.000 miles) is recommended to guarantee a lasting effect.
Viscoplus for Oil
Show details
Viscoplus for Oil
Viscoplus for Oil
Properties
- reduces engine noise
- reduces oil consumption
- optimum oil pressure under all operating conditions
- stabilizes loss of viscosity
- optimum lubrication under all operating conditions
- fully compatible with mineral and synthetic oils
- improves the movable seal between piston and cylinder
- reduces wear
Application
One full can (300 ml) used with 3–5 Liters (3.2 to 5.3 U.S. Qts) of motor oil. The product is self-mixing and can be added at any time. Shake well before use. Ideal for top-up use.
